I just gotten my industrial shield. However I am facing issue programming the Arudino.
Getting avrdude: stk500v2_ReceiveMessage(): timeout
Anyone else face this before?
0
1 Respuesta
0
<div>
<h5 class="o_wforum_bio_popover_name mb-0">
<address class="mb-0" itemscope="itemscope" itemtype="http://schema.org/Organization">
<div>
<span itemprop="name">Andrei Postolache</span>
</div>
<div itemprop="address" itemscope="itemscope" itemtype="http://schema.org/PostalAddress">
</div>
<div>
</div>
</address>
</h5>
<span class="o_wforum_bio_popover_info">
<address class="mb-0" itemscope="itemscope" itemtype="http://schema.org/Organization">
<div class="css_non_editable_mode_hidden">
--<span class="text-muted">Andrei Postolache</span>--
</div>
<div itemprop="address" itemscope="itemscope" itemtype="http://schema.org/PostalAddress">
</div>
<div>
<div class="css_editable_mode_hidden">
<div class="mb-2">
<br/>
</div>
<b class="mt-4"><i class="fa fa-diamond text-secondary"></i> 2000000000</b>
<div style="display: inline-block">
<b>|</b>
<span class="fa fa-trophy badge-gold ml-2" role="img" aria-label="Gold badge" title="Gold badge"></span>
0
<span class="fa fa-trophy badge-silver ml-2" role="img" aria-label="Silver badge" title="Silver badge"></span>
0
<span class="fa fa-trophy badge-bronze ml-2" role="img" aria-label="Bronze badge" title="Bronze badge"></span>
0
</div>
<div class="mt-2">
</div>
</div>
</div>
</address>
</span>
<div class="o_wforum_bio_popover_bio">
<address class="mb-0" itemscope="itemscope" itemtype="http://schema.org/Organization">
<div class="css_non_editable_mode_hidden">
--<span class="text-muted">Andrei Postolache</span>--
</div>
<div itemprop="address" itemscope="itemscope" itemtype="http://schema.org/PostalAddress">
</div>
<div>
<span>
</span>
</div>
</address>
</div>
</div>
</div>
">
Best Answer
Hello Danny,
There could be one of the four possible reason behind it. They are:
Wrong Port Selected:
If
TX/RXled is not blinking, then you may have selected wrong port. If one of both of them are blinking then, you aren't using the wrong port. It might be worth checking again though, sometimes USB COM devices install on strange port numbers.Board is not in
BootloaderMode:The
Arduino Megais not executing thebootloaderfor some reason. If the programmer is not resetting the micro before attempting to connect, this might be the reason. Try to reset the board (press and release the button) while the programmer is attempting to connect. Sometimes software that runs in a tight loop will prevent thebootloaderfrom connecting. Barring that, the fuses might have gotten messed up or the code erased. You would need to reflash the bootloader and proper fuses, again, see the appropriate info page for your device.Arduino Mega 2560 only: ATmega8U/16U software
Might not be working and would need reprogramming. See the Programming section on the info page, you will need the firmware and Atmel-compatible DFU (device firmware update) software on your computer to
reflashthe target.Hardware damage:
There could be hardware damage to the board, AVR(s), or FTDI chip.
You can contact us on the Technical Support email or Whatsapp.
Thank you.
1
Comentario
Danny Ng
-
Manage to get the issue sorted out when I submitted a ticket on this. Following guide I get from the ticket, I plan to change the Arduino unit. However the unit work fine after I have taken out the Arduino and notice that the Arduino can be programmed so I did not change the Arduino and assemble the unit again.
After reassembling the unit and I notice that It can work. I think it might be due to shipping causing some part to went loose.
Got it sorted out at the end.